OpenSeaMap-dev:HW-logger/OSeaM-Manual(en): Unterschied zwischen den Versionen

Aktuelle Version vom 6. Juni 2018, 08:52 Uhr

Sprachen:	Deutsch	English

NMEA-0183 Logger

Actual Firmware for 2x NMEA: V0.1.12

Actual Firmware for Seatalk: V0.1.15

Developer pagee: http://wkla.no-ip.biz/ArduinoWiki/doku.php?id=arduino:oseam (German)

Preface

The OpenSeaMap data logger is capable of logging data of two NMEA-0183 devices, for example depth-sounder and GPS. For this, there are two input channels. Both inputs will be written with a timestamp for a later chronological sorting. Data about acceleration and displacement will also be logged to determine heeling, heaving and pitching. All data will be written to an SD-card. Data is recorded raw for further processing, no filtering is done.

Features

Data logger for NMEA-data
Built-in 6-axis MotionTracking (Gyroscope and Accelerometer)
Writing data on standard SD-card in NMEA-0183 format
Simplest handling
LED for operation, input data, and SD-card access
2 NMEA-0183 inputs (4800 Baud)
1 Seatalk-1 input alternatively (selectable by internal jumper)
12 V supply

Delivery

Package

Logger and cable

You can order the NMEA-Logger here.

It comes to you in a small packet.

Content: 1 NMEA-Logger; 1 Cable with RJ45 jack and open end; Manual in English and German

Installation

Mounting the Logger

Install the logger to a protected location where you have access to the SD-card and where you can see the LEDs.

Mount it as perpendicular as possible to the front panel of the navigation area (outside or inside) or perpendicular to a vertical wall behind. The top edge ideally will be horizontally to the ship's transverse axis. The two arrows on the upper surface indicate the direction in respect to the ship's axis. Please describe this in the metadata of your ship.

Connecting the Cable

The logger will turn on automatically with the operating voltage. After switching on, it takes about 30 seconds until the logger starts to write data. If the green power indicator LED is lighting, the logger is active and ready to receive. The connection is made via the RJ45-jack. This is where all signals and the supply are connected.

A suitable cable comes with the logger. In case that you need to buy a longer one, please use a simple normal patch cable (network cable) as it is available at any electronics store. Make sure that this is not a "crossover" cable" or "cross cable" for directly connecting two computers. Cut the patch cable, you need one side (connector and open end). The colors show you if the cable is European or American. If the outer wires in the tranparent plugs are green, you've got a cable according to the European standard (568A), if these are orange it is an American standard cable (568B).

There are the following connections:

Plug

American patch-cable.
The outer wires are orange.

Conductor pairs

Pin	-568A pairno.	-568B pairno.	-568A color (Europ. cable)	-568B (AT&T 258A) color (American cable)	Logger meaning
1	3	2	white/green line	white/orange line	Seatalk -
2	3	2	green/white or green	orange/white line or orange	Seatalk +
3	2	3	white/orange line	white/green line	NMEA B -
4	1	1	blue/white line or blue	blue/white line or blue	NMEA A +
5	1	1	white/blue line	white/blue line	NMEA A -
6	2	3	orange/white line or orange	green/white line or green	NMEA B +
7	4	4	white/brown line	white/brown line	GND
8	4	4	brown/white line or brown	brown/white line or brown	+12V

CAUTION: In the printed manual channel A and B are interchanged.

Connecting the Sounder NMEA

Connect the NMEA output of the sounder/sonar to the NMEA input of the logger.
Use the NMEA-A for the sounder/sonar if possible.

Signal Sonar	NMEA-A
-	Pin 5
+	Pin 4

If the Sounder works with Satalk-1, see switch port A from NMEA-0183 to Seatalk-1.

Connecting Sounder Seatalk

Connect the Seatalk-1 output of the sonar to the Seatalk-1 input of the logger.

Jumper for NMEA (default)

Jumper for Seatalk

Signal Sonar	Seatalk
-	Pin 1
+	Pin 2

The input A has to be switched electrically from NMEA-0183 to Seatalk-1.

For this, there are two steps necessary:

Open the logger. There is a red jumper in the middle of the board. On the board you will find the words "Seatalk/NMEA". For Seatalk, put the bridge on the left and the middle pin (where "Seatalk" is written). For NMEA, put the bridge on the right and the middle pin (where "NMEA" is written).
Start the configuration program and create a configuration file with the appropriate entries. Save this configuration file on an SD-card and start the logger with this card.

Connecting GPS NMEA

Connect the NMEA output of the GPS device to the NMEA input of the logger.
Use the NMEA B for the GPS if possible.

Signal GPS	NMEA-B
-	Pin 3
+	Pin 6

Connecting Supply (12 V)

The logger is operating with 12 V voltage (9-15V). To start the data recording automatically when the navigation devices are turned on, the logger must be connected to the same circuit as the navigation instruments.

Supply	Cable	Color
GND	Pin 7	white/brown line
+12 V	Pin 8	brown/white line or brown

Connecting Cable

Terminal strips are ideal. If you connect the cable to a terminal block, you can bend the stripped end, in order to fix it better in the terminal block.

Strain Relief

The loose end of the cable must be secured with a strain relief when connected to the onboard electronics (the wires are very thin).

Functions

After applying the operating voltage and a short initialization time (30 seconds), the data is written automatically to the SD-card.

Control Panel

The control panel is self-explaining:

SD-card	Insert SD-card	We recommend a 4 GB SD-card. It can record up to 40 days. The SD-card must be formatted FAT-32.
Active/write	Green Red flashing	The logger is active and ready to receive the logger writes to the SD-card.
RJ45-Connector	Connect power supply Connect sonar Connect GPS Gelb/Green flashing	On the NMEA channel, a valid signal is received.

Insert the SD-card before turning on the logger.
Remove the SD-card from the logger only when the logger is turned off.

On every start and every hour, a new file will be created automatically on the SD-card.

Errors

If an error of writing the data occurs during start or operation of the logger, the red LED flash regularly every second:

Where	What	Meaning	Action
LED next to plug	Red flashing	SD-card is full.	Replace SD-card with an empty one.

Other possible causes:

SD-card has an unsupported file format (for data cards there is only FAT-16 and FAT-32 supported)
SD-card is not writable or is not recognized. Please test the card on your PC.

Operating LEDs

Where	What	Meaning
LED next to plug LED 1 in plug LED 2 in plug	Green off off	The logger is active and reciving.
LED next to plug LED 1 in plug LED 2 in plug	Green flashing	Initialization of the logger (about 30 sec)
LED next to plug LED 1 in plug LED 2 in plug	Red	The logger is currently turning off.
LED next to plug LED 1 in plug LED 2 in plug	Red flickering	The logger is writing data on the SD-card.
LED next to plug LED 1 in plug LED 2 in plug	Yellow flickering Green flickering	In this NMEA channel, a valid signal is received. In this NMEA channel, a valid signal is received.

Preparing the SD-card

We recommend a 4 GB SD-card. It can record up to 40 days. (about 4 MB per hour, 100 MB per day). The SD-card must be formatted FAT-32.

Firmwareupdate with SD-card

A SD-card with FAT-16 file system must be used for the firmware update. The easiest way is to use a SD-card with 2 GB or smaller. This can be simply formatted with FAT-16 (on some operation systems are also just plain FAT) or creating a small partition. The latest firmware file can be downloaded, and put on the root of the SD-card.

A software tool that simplifies the update process is in progress.

Firmware-Version	Date
xxx	yyy

Programm "OpenSeaMap-Logger"

Mit dem Programm "MCS Depth-Logger" kann man Tiefen-Daten hochladen und den Logger konfigurieren:

Verwaltung/Backup/Restore der SD Karten
Verwaltung der Firmware inkl. Vorbereitung der SD Karte für ein evt. Firmware Update
Überprüfung/Korrektur der geloggten Daten
Export ins NMEA Format
Upload auf einen Server
Darstellung einzelner Daten auf Karten
Verwaltung von Routen
1. Hinzufügen/Löschen von einzelnen Dateien
2. Darstellung auf Karte
Kartendarstellung
1. verschiedene Kartenprovider: OpenStreetMap, OpenSeaMap, Virtual Earth
2. Möglichkeit verschiedener Overlays wie Sportstätten, Seezeichen
3. Darstellung verschiedener Daten als Diagramm: Tiefe, Höhe, Beschleuningung und Lage, Geschwindigkeit
Internationalisierung: Sprachen Deutsch und Englisch, Maßsysteme: metrisch, imprial, nautisch

Manual for "MCS Depth Logger"

Operation

For the skipper

Start: If the logger is connected to the power supply of Navigation Devices,
it starts automatically when the navigation devices are turned on.

If the navigation devices be turned off (or if a power interruption),
the log file is automatically closed.

Once the power supply is switched on again, a new file is created automatically.

The logger has an built-in power-backup-circuit
ensuring there is no data write fault during interruption of the supply voltage.

SD-card: On an SD-card with 2 GB can be recorded for about 18 days.
Approximately 100 MB of data recorded per day.
(This can of course vary according to the GPS and sonar used.)

Thus, the SD-card needs to be replaced in time.

For Charter Combapies

For simple handling, use 2 SD-cards to each device.

After each charter trip the SD-card needs to be replaced.

To do this, label for each vessel 2 SD-cards with the ship's name.
One card is plugged into the logger, the other comes into the office to vessel/charter-documents.

The logger automatically starts with the navigation device.
The charter customers don't need to worry about anything.

The following check lists can be adapted to your charter base:

When crew changes

Remove the written SD-card
Insert new empty card (from the vessel documents)
Bring removed card with the ship's documentation to the office

During crew briefing: It would be nice if the charterers employee in charge briefly tells that the charter company participates in the project "Detection of shallow water depths". And that the skipper can support the project particularly well by selectively moves a bit in bays and harbor entrances back and forth to capture the depth of the key points well.

This could also be advertised on your website.

In the office

put removed card into a PC and upload data to the server.
assign the uploaded data to the correct ship (choose from the list of vessels)
Erase data on the described card,
put the empty card to the shipping documents.
Note in the ship's documentation:
Data uploaded <trip/customer> <date>
Data deleted <trip/customer> <date>

Meta data

For a reliable evaluation, we need accurate information about the ship and the measuring device used.

These data need be entered only once per vessel and are then valid for all log files for this ship. Changes to marine electronics, the original data can be easily changed or expanded.

Uploading data

You need a computer with Internet connection and SD-card reader
Put the SD card into the SD-card slot
Please log in using your username: http://depth.openseamap.org
Enter the metadata of your ship and to the measuring device.
If you use the same ship as the last time, and if nothing was changed in the measuring device, you can simply select your ship from the list of your ships.
Upload the data to the server

Credits

OpenSeaMap says thanks to:

Wilfried Klaas: for developing the hard- and software

KoBo Trading Company Limited, HongKong: for prefinancing

KoBo (Shenzhen) electronics company Limited, Shenzhen, China: for prototyping and production

AK Modulbus GmbH: for distribution, but AK Modulbus can not spend any technical support for the logger.

Küstenschmiede: for Logger distribution: shop4gis.com